12 volt relay for fuel injection system

4 pin relay, also known as Guzzi ref. 895481

 2 in stock

AP8124869

Also fits Aprilia 1000 RSV4 R APRC , BJ 2013 - 2014, Aprilia 1000 RSV4 RF , BJ 2017 -, Aprilia 1000 RSV4 RR , BJ 2015 - 2015, Aprilia 1000 RSV4 RR , BJ 2016 - 2016, Aprilia 1000 RSV4 RR , BJ 2017 -, Aprilia 1100 Tuono V4 Factory , BJ 2015 -, Aprilia 1100 Tuono V4 RF , BJ 2017 - 2019, Aprilia 1100 Tuono V4 RR , BJ 2016 - 2017, Aprilia 1100 V4 Tuono Factory , BJ 2017 -, Aprilia 1200 Caponord Rally , BJ 2015 - 2017, Aprilia 1200 Caponord Travel Pack , BJ 2013 - 2016, Aprilia 750 Shiver , BJ 2014 - 2017, Aprilia 900 Dorsoduro , BJ 2017 -, Aprilia 900 Shiver , BJ 2017 -

Set of leads for batter charging. Ring terminals for battery, 2 pin connector for charger to plug into. Often required if you charge more than one bike using your Motobatt Smart Charger

 2 in stock

Universal hydraulic brake light switch. This hydraulic switch replaces discontinued brakelight switches by bolting in place of a single banjo bolt on the handlebar or rear brake master cylinder

NB stop light switch may be supplied with or without 2 pin block connector. Can be used in place of Guzzi ref. 32657060

 1 in stock

Domino left hand switchgear with lights on - park - off, high and low beam, pass, indicator and horn switches. Same style switch as ELA01738.

Already wired in to 9 pin block connector (you may need to alter the wiring on your bike to correspond to this block connector). Originally fitted as standard to early V11 Sport models. See the wiring diagram on our technical documents page for help installing this switchgear. See Greg Bender's website for a custom sub-loom that enables easy fitting of this part to models previously fitted with LEGO style swithgear

 1 in stock

 01738030 GU01738030 01 73 80 30
 0173 8030 0173.8030 01.73.80.30

Right hand Domino type starter switch for use with separate throttle, e.g. Tommaselli twin pull throttles ACA10500 or ACA10501

On most bikes this will not plug directly into the wiring loom, you will need to match the wires to your loom. If replacing 'Lego' type switchgear (e.g. Le Mans 2, V50) with integrated twistgrip you will need a separate twistgrip, see ACA10500 and ACA10501. Packaging may include explanation of switchgear wire covers. This type originally fitted as standard to the early V11 Sport models. See the wiring diagram on our technical documents page for help installing this switchgear.. Molex connectors available separately.

 1 in stock

 01738800 GU01738800 01 73 88 00
 0173 8800 0173.8800 01.73.88.00

Alternator belt

 1 in stock

 05702530 GU05702530 05 70 25 30
 0570 2530 0570.2530 05.70.25.30

6 pin male block connector, used for main loom connections. See ELA30001 for female 6 block connector.

 1 in stock

200073020

Dipped beam bulb H7 12V 55W for headlight

 1 in stock

AP8127109

Universal hydraulic brakelight switch. This hydraulic switch replaces discontinued brake light switches by bolting in place of a double banjo bolt on the handlebar or rear brake master cylinder

Especially suitable for replacing the standard switch on models where the front brakes have been 'de-linked'

 1 in stock

Halogen headlight bulb H3 12V 55W. Dipped beam bulb for headlight. Used as spotlight bulb on Cali Vintage

Also known as Guzzi ref. 30530558

 1 in stock

 294278 MG294278